| Model SPS | | Model SPS | | | Part # | Description | Part # | Description | | 31001 | SHEAR PLATE HOLDER | 31045 | HOLD DOWN SCREW DETAIL | | 31002 | FRAME | 31049 | FEED HOPPER DETAIL | | 31003 | BELT GUARD | 31050 | FEED HOPPER DETAIL | | 31004 | BEARING HOUSING | 31051 | FEED HOPPER DETAIL | | 31005 | SLICING UNIT BRACKET | 31053 | FEED HOPPER DETAIL | | 31006 | LOCK PIN | 31057 | PLASTIC TAG HOLDER | | 31007 | BALL BEARING | 31058 | FLOOR STAND | | 31008 | OIL SEAL | 31059 | FLOOR STAND, DETAIL | | 31009 | OIL SEAL | 31060 | FLOOR STAND, DETAIL | | 31011 | PULLEY, V, 3.00 OD, .938 ID, 2 GROOVE | 31061 | FLOOR STAND, DETAIL | | 31013 | LOWER BEARING LOCK SLEEVE | 31062 | FLOOR STAND, DETAIL | | 31014 | BEARING SPACER COLLAR | 31063 | FLOOR STAND, DETAIL | | 31015 | BEARING SPACER SLEEVE | 31064 | FLOOR STAND, DETAIL | | 31016 | SHAFT, SPINDLE | 31065 | GREASE TUBE | | 31017 | SEAL HOLDER, UPPER | 31066 | FRAME, 182 AND 184 MOTORS | | 31018 | SEAL HOLDER, LOWER | 31071 | PULLEY, V, 2.80 OD, .875 ID, 3 GROOVE | | 31020 | BEARING HOLDER | 31072 | PULLEY, V, 2.80 OD, .938 ID, 3 GROOVE | | 31021 | FEED CONE NUT | 31073 | PULLEY, V, 4.12 OD, 1.125 ID, 3 GROOVE | | 31022 | SLICING WHEEL NUT | 31074 | V BELTS, 3VX450, SET OF THREE | | 31023 | FEED CONE | 31076 | PULLEY, V, 4.12 OD, .875 ID, 3 GROOVE | | 31024 | BEARING SHIELD | 31077 | PULLEY, V, 4.12 OD, 3 GROOVE | | 31025 | HOLD DOWN SCREW | 31078 | HUB | | 31030 | WASHER FOR DRIVE PULLEY | 31079 | HUB | | 31032 | SLICING WHEEL PULLER | 31080 | FEED HOPPER, SPECIAL | | 31033 | FEED HOPPER | 31081 | HOLD DOWN SCREW DETAIL | | 31034 | DISCHARGE CHUTE | 31094 | SENSOR BRACKET | | 31035 | BELT GUARD PLATE | 31095 | BRACKET FOR STARTER | | 31037 | KNIFE CLEARANCE GAUGE | 31097 | BRACE | | 31039 | WHEEL ASSEMBLY, SLICING, 5 KNIVES | 31098 | MOTOR, 5 HP, 230/460V, W/BRAKE | | 31042 | FEED HOPPER DETAIL | 31103 | WIRING DIAGRAM, ANSI | | 31043 | PLASTIC STOCK FOR 31037 | 31104 | ELECTRICAL ASSY, MODEL SPS | | | 31105 | WIRING DIAGRAM, MODEL SPS |
A partir del 1° de enero de 2010, una cantidad determinada de piezas para equipos Urschel sumamente antiguos u obsoletos quedarán descontinuadas. Antes del 1° de enero de 2010, los clientes tienen la oportunidad de colocar pedidos por cantidades grandes de las mencionadas piezas descontinuadas. Después de dicha fecha, estas piezas ya no se fabricarán, pero Urschel continuará ofreciendo las piezas mientras existan en inventario. En caso de preguntas, comuníquese con el representante local de Urschel. |
